on my last trip, my sail ripped all the way down, I lost control in the current and got pushed onto some rocks.

Luckily, the boat didn't sink, and some fishermen came to help me.

I need to fix the damage to the hull,

do you think I need to use fiberglass, or is gelcoat enough?

what steps should I follow to repair it properly?

Need help identifying this vessel.

Looks amphibian, but it's probably not.

Located in Scandinavia, if it's any help.

TIA

I'm a crewman for Fuel 1 Team, everyone this weekend was absolutely amazing! Especially with the Thundercats ;)

Come catch us next month in Key West!

Been shopping around & found this boat. I’ve tried to use all the boat value calculators and I can’t seem to narrow in on a good price. Help? This is my first boat.

I am currently trying to decide if I want to purchase this saltwater boat. It comes with the mounting unit for a Garmin device. However, the owner does not have the device and does not know what unit goes for this mount.
If anyone has any knowledge on what device fits in this unit I would be greatly appreciative.

Got myself a boat with a Honda BF100A (2024). Engine is only on 60hrs and has been stood a while, although serviced in June.

Tis a bit noisy/slow when raising. Am I right to assume there's some air in there and topping off with fluid should see me right? Potentially drop the fluid to check for any presence of water? Something more sinister? Cheers!

Taking my boat out of the water this weekend and I'm debating storing it at my house instead of at a marina because last winter, mice tore up my upholstery when the marina sored it in a field. How can I prevent mice from getting into my boat

Are any of these used boats for $2500-4500 actually worth it? I understand some work might have to be put in. But I’m just looking for a nice fishing boat for mostly calm waters. It would be my first boat and I understand it won’t be my dream one. But is it possible to find a decent boat in this range and slowly upgrade as I go?

Need a 5hp motor for my s15 sportspal canoe. Found a guy on marketplace with a Honda BF5. Says he hasn’t run it since July but Honda is a good brand. It’s going for $500. Asked my dad and he said to go for a mercury or evinrude.

Been between propane and gas. Leaning towards gas because mechanic reliability and help on the water. But I’m also kind of lazy and don’t take my boat out that much except for in the fall. Should I really go gas? Any benefit to propane?

Any surprises or suggestions? I have an electric trolling motor and it’s been great just looking for longer and faster.

I have had this boat for three years and on my second pulley replacement due to salt/brackish water and/or coating of steel pulleys failing.

After discussing with manufacturers about making the steel pulleys out of stainless steel, I’m interested in the market’s opinion. Would you be willing to buy a stainless pulley even if the price was double?

Currently have a 2011 30hp tiller Merc with electric start and trim.

Having issues with the electric start. If it doesn't beep initially it will not start. It's like I need to start/stop the motor 3 or 4 times before the beep goes and then it will fire up.

Ok guys I need some help. I guess I hit something in the water and broke my transducer on my depth finder. I tried JB weld but no luck. So where can I buy one and also does it have to be required all the way back to the screen or is there a connection somewhere up line. Or do I have to cut and splice.

Hey guys, so bought a sweet little Tracker Grizzly 1650T and it’s a nice little boat. however, it has a freaking 2” transom plug. I was supplied with a 2” PVC plug for it(how crappy is that?)

Does anyone have a good upgrade for it? Thats currently my only complaint about the boat but it’s really a pain in the ass to have to bust out the channel locks every time I get home and have to run that long winded plug out

Thank you!

I’ve googled and checked old forums and couldn’t find any conclusive advice so I wanted to come here; apologies if this is a dumb question.

I have a 95 Bayliner with a 120HP Force motor that I use restored this summer. The motor had less than 200 hours on it and replacing the rotten decking was the major challenge.

I performed a complete motor service and replaced a bad stator and found the integral tilt/trim cylinder had a leak around the seal. I replaced the tilt/trim motor and refilled the cylinder and confirmed the tilt/trim works perfectly and the cylinder is at full capacity when level.

I took the boat out to the water a few weekends ago and at the dock, I was able to trim the motor down into the water, reverse from the dock, and at low speed, I have full tilt/trim control. As I got underway, I was nosing up too high so I tried to trim up to bring the bow down and found that while underway, tilt/trim does not move the motor. I can hear the relay click under the cowling and I’m certain voltage is happening but no dice on movement.

I was just out fishing so I putted around the lake without issue. When I returned to the dock, I was in the same scenario that under low speed, the tilt/trim still works and once I was on the trailer I was able to tilt the motor fully out of the water.

In the driveway, I’ve tested that, while pushing back against the motor to add force against the cylinder, tilt/trim operates fine. It only appears to happen when underway.

Any suggestions on what it could be? I tested the kill switch and the Force 120HP doesn’t have any special tilt controls other than over current protection when at full up/full down positions and didn’t seem like that was my cause either.

Hello all,

Looking at getting my first boat (already signed up for some boating academy classes) and after some research it seems like these fit my size, budget, use preferences.

Was curious while shopping Ive seen numerous 2026 models and a few leftover 2024 models. Does anyone know of any significant differences in the two years? From what I gather the hull itself hasnt changed but I wanted to be sure Im not missing something.

As a first time owner, going with a 2024 model and savings 8-10k seems like a smart play.

Thanks!

We surveyed the full wooden frame in the jungle - from Bow to Transom - before stringers. Follow the Wooden Shoe station by station as Victor and Per check every joint, gap and epoxy fix before locking it forever. After stringers go on, it's very difficult to fix inside — so this is our last chance to get it right.

The Bow, Keel to Bow glued, screwed and planed to a smooth curve, Station 1 OK, Station 2 Add Gflex epoxy in gaps, Station 3 OK, Station 4 OK, Station 5 Add Gflex epoxy, Station 5.5 OK, Station 6 OK, Station 7 Add Gflex epoxy, Cockpit Sole missing second layer epoxy, Station 8 OK, Station 9 gap rear side, Station 10 gap front side, Station 11 OK, Station 12 OK, Station 13 add Gflex epoxy in gap, Station 14 Transom must be glued and screwed from the top, support structures walk-through, ending with Now we have the points and lets fix this!

Building a 25FT Wooden Shoe powerboat from scratch in Mexico with Chechen wood and Cumaru hardwood. No fancy workshop — just lofting, framing and honest fixes.

Now we have the points and lets fix this!

Please sign to help save the lady Washington

Noticed the separation between the nut on the steering support rod. I am guessing this isn't normal and in need of adjustment. Is there a manual or adjustment guide with torque specs I should follow? Or any other help? Thanks.